FAQ – DRAMINSKI Dog Ovulation Detector | Dog breeds, Dog breeding for dog breeders, Breeding Your Dog

FAQ – DRAMINSKI Dog Ovulation Detector

How to clean the instrument?

Disinfect the detector before and after each measurement. Careful and thorough cleaning and disinfection of the instrument are the most important conditions for its proper usage. Always use disinfectants at concentrations given by the manufacturer, as otherwise they may cause irritation of the vaginal lining. Clean the instrument before each use to prevent this. The solution of the disinfecting agent should be prepared directly before the next use of the detector. The best disinfectant agent is Hibiscrub, Dettox or Savlon solutions, or any other agent indicated for veterinary use. Wipe the surface of the probe with the solution, then rinse thoroughly with water, dry and put into a box.

Can the instrument be used when the bitch has problems?

Well, the problems will remain. Obviously this instrument will not solve the reproduction problems of a bitch. It will not change an infertile bitch into a fertile one. However, it is another instrument to facilitate managing reproduction programs. This instrument can be used at home. It will reduce the number of visits at the vet’s as well as the number of more expensive and invasive tests. It will help to determine false heat because in such a case a value of the reading will not increase. Also in the case of quiet heat the peak of climax can be determined precisely.

Can the probe be used after mating?

Yes, it can; it should not have any adverse effects.

How will I know that the probe is in an adequate place?

The probe should be inserted until light resistance is felt when the probe reaches the cervix. It constitutes approx. 3/5 of the probe length (namely 3 inches inside and 2 inches outside). In this place the tip of the probe is in the area containing the highest concentration of mucus what allows to achieve a precise and reliable reading. This position changes slightly depending on the size of a bitch. Moreover, in some bitches the cervix is very widened in the initial phase of a cycle and while inserting the probe no or slight resistance is felt. However, the rule 3/5 of length is still valid.

I receive a different reading after the probe has been inserted and when I press the button once again without moving the probe.

The possible reason is a difference in temperatures. Temperature affects the results. If the probe is kept in the vagina longer, it warms up and as a result subsequent results are different. Therefore, it is so important to perform measurements always in the same manner. The results read after a few seconds are more reliable, because the temperature of the instrument is similar to the temperature of the bitch body. The same method should be continued during all subsequent measurements.

I get random high readings. Why?

It usually happens when the probe is inserted too deep into the vagina (namely, the whole probe is inserted, up to the instrument housing). In this way it passes through the cervix resulting in random high readings.

All readings show low values (they do not exceed 150 or 200) – why?

It usually happens when the probe is inserted too shallow into the vagina (namely into the vulva) and there is no contact between the probe and the mucus which is the object of measurements. Moreover, the presence of salts in the urine may decrease the readings.

Why is there a difference between morning and evening measurements?

There is no “best time” to perform measurements. However, we have noticed that there might be differences between morning and evening measurements in some bitches.

We recommend to prepare charts for morning and evening readings. Although morning and evening measurements might be different, the profile of changes is the same. The peak value will appear at the same time.

How often should measurements be performed?

It is the best to perform them at the same time every day, if it is possible. As the procedure is so easy and fast, when readings start to increase it is recommended to perform 2, 3 or 4 measurements a day in order to determine the peak value very precisely, namely to determine the best time for mating.

Can I perform the procedure alone?

Yes, and the method is the same as while mating. However, another person is very helpful as they can hold a bitch during a measurement what should facilitate performing of the procedure.

Will my bitch suffer from pain?

No, unless you are very heavy handed and if you take obvious care and attention ~ the size of the probe (length & diameter) is similar to the penis of the dog (even in toy breeds). Each bitch is different and some of them accept the probe immediately at the first use, some of them seem surprised and others – worried, it is a similar reaction when a bitch reacts to a stud dog while mating.

How does the instrument work? Is its action connected with the temperature measurement?

No, the instrument measures the electrical resistance of vaginal mucus in the area of the cervix.

dreamstime_2627012m